New installation.
I tried to rewrite a previous version of the card but did not succeed. this journal entry was generated.
+00: 00 (, 0) Starting emteria installer v0.5-2-g55cc940
+:: (Qrc: /main.qml, 221) qrc: /main.qml: 221: 17: QML Rectangle: Binding loop detected for property "height"
+00: 30 (, 0) Refreshing drives
+00: 32 (, 0) Found 2 drives
+00: 41 (, 0) Downloading "package.json"
+00: 41 (, 0) Using path "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8/package.json"
+00: 41 (, 0) Finished download of "package.json"
+00: 41 (, 0) Checking for OEM config ...
+00: 41 (, 0) Retrieved OEM config config = 0
+00: 41 (, 0) Downloading "boot.zip"
+00: 41 (, 0) Using path "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8/boot.zip"
+00: 44 (, 0) Finished download of "boot.zip"
+00: 44 (, 0) Downloading "oem.zip"
+00: 44 (, 0) Using path "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8/oem.zip"
+00: 44 (, 0) Finished download of "oem.zip"
+00: 44 (, 0) Downloading "system.zip"
+00: 44 (, 0) Using path "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8/system.zip"
+01: 06 (, 0) Finished download of "system.zip"
+01: 06 (, 0) Finished DownloadWorker
+01: 06 (, 0) Flashing on raw "\\\\\\ PHYSICALDRIVE3"
+01: 06 (, 0) Initializing PackageWriter
+01: 06 (, 0) Package base path: "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8"
+01: 06 (, 0) Drive: "Generic Multi-Card USB Device" with 31914983424 bytes
+01: 06 (, 0) Raw at "\\\\\\ PHYSICALDRIVE3"
+01: 06 (, 0) PackageWriter initialized successfully
+01: 06 (, 0) Starting step 0 Reading package
+01: 06 (, 0) Finished step 0 Reading package
+01: 06 (, 0) Starting step 1 Verifying files
+01: 12 (, 0) Finished step 1 Verifying files
+01: 12 (, 0) Starting step 2 Preparing
\ R \ nComputer: DESKTOP-BJVR45J \ r \ n \ r On the computer: +01: 22 (, 0) Diskpart output: "\ r \ nMicrosoft DiskPart version 10.0.16299.15 \ \ n \ r \ nDiskPart has succeeded in cleaning the disk. \ n \ r \ nPlease wait while DiskPart scans your configuration ... DiskPart has finished scanning your configuration. \ r \ n "
+01: 22 (, 0) Diskpart error: ""
+01: 24 (, 0) Finished Step 2 Preparing
+01: 24 (, 0) Starting step 3 Opening to write
+01: 24 (, 0) Finished step 3 Opening to write
+01: 24 (, 0) Assuming drive has 62333952 sectors
+01: 24 (, 0) Processing 4 partitions
+01: 24 (, 0) Processing partition "boot"
+01: 24 (, 0) Using LBA of 2048
+01: 24 (, 0) Size determined from zip source: 65011712
+01: 24 (, 0) Partition will occupy 126976 sectors
+01: 24 (, 0) Processing partition "system"
+01: 24 (, 0) Using LBA of 129024
+01: 24 (, 0) Size determined from zip source: 2147483648
+01: 24 (, 0) Partition will occupy 4194304 sectors
+01: 24 (, 0) Processing partition "oem"
+01: 24 (, 0) Using LBA of 4323328
+01: 24 (, 0) Size determined from zip source: 536870912
+01: 24 (, 0) Partition will occupy 1048576 sectors
+01: 24 (, 0) Processing partition "userdata"
+01: 24 (, 0) Using LBA of 5371904
+01: 24 (, 0) Processing dynamically sized partition "userdata"
+01: 24 (, 0) Partition will start at LBA 5371904
+01: 24 (, 0) Remaining sectors on drive: 56962048
+01: 24 (, 0) Starting step 4 Writing MBR
+01: 24 (, 0) Partitions in MBR:
+01: 24 (, 0) Partition 0 bootable true LBA 2048 size 126976
+01: 24 (, 0) Partition 1 bootable false LBA 129024 size 4194304
+01: 24 (, 0) Partition 2 bootable false LBA 4323328 size 1048576
+01: 24 (, 0) Partition 3 bootable false LBA 5371904 size 56962048
+01: 24 (, 0) Finished step 4 Writing MBR
+01: 24 (, 0) Starting step 5 Writing file
+01: 24 (, 0) Using zip file at "C: /Users/tieff/AppData/Local/Emteria/Installer/rpi3-v0.5.8/boot.zip"
+01: 24 (, 0) Failed writeRaw: 0
+01: 24 (, 0) Tried to write 8388608 bytes
+01: 24 (, 0) error in mz_zip_reader_extract_to_callback
+01: 24 (, 0) Failed extracting the zip file: write calledback failed
+01: 24 (, 0) Failed unzipping file
+01: 24 (, 0) Failed to write partition content for "boot"
Comments
I put the card in RPI in a hurry.
Only REVOVERY worked
If that helps.
The installation process heavily depends on your hardware (pc / sdcard reader / sdcard). If one of these components doesn't work properly, our software fails to write the data. There is no standard way of solving this issue - it is related to your hardware. Try again or use another sdcard.
This is a quality SD card, specifically bought for this project. Please help me how I can form the card. What I found on the net I tried everything but none succeeded. They are recognized as read-only and I can not stop it. Please help with the solution because the card has been added, which is the key to the OS program.